fence_brocade - Fence agent for HP Brocade over telnet/ssh
fence_brocade is an I/O Fencing agent which can be used with
Brocade FC switches. It logs into a Brocade switch via telnet and disables a
specified port. Disabling the port which a machine is connected to
effectively fences that machine. Lengthy telnet connections to the switch
should be avoided while a GFS cluster is running because the connection will
block any necessary fencing actions. After a fence operation has taken place
the fenced machine can no longer connect to the Brocade FC switch. When the
fenced machine is ready to be brought back into the GFS cluster (after
reboot) the port on the Brocade FC switch needs to be enabled. This can be
done by running fence_brocade and specifying the enable action
fence_brocade accepts options on the command line as well as from
stdin. Fenced sends parameters through stdin when it execs the agent.
fence_brocade can be run by itself with command line options. This is useful
for testing and for turning outlets on or off from scripts.
Vendor URL: http://www.brocade.com
- -o,
--action=[action]
- Fencing action (Default Value: off)
- -c,
--command-prompt=[prompt]
- Force Python regex for command prompt (Default Value: ['> '])
- -k,
--identity-file=[filename]
- Identity file (private key) for SSH
- -4, --inet4-only
- Forces agent to use IPv4 addresses only
- -6, --inet6-only
- Forces agent to use IPv6 addresses only
- -a, --ip=[ip]
- IP address or hostname of fencing device This parameter is always
required.
- -u,
--ipport=[port]
- TCP/UDP port to use for connection with device (Default Value: 23)
- -p,
--password=[password]
- Login password or passphrase
- -S,
--password-script=[script]
- Script to run to retrieve password
- -n, --plug=[id]
- Physical plug number on device, UUID or identification of machine This
parameter is always required.
- -x, --ssh
- Use SSH connection
- --ssh-options=[options]
- SSH options to use
- -l,
--username=[name]
- Login name This parameter is always required.
- -q, --quiet
- Disable logging to stderr. Does not affect --verbose or --debug-file or
logging to syslog.
- -v, --verbose
- Verbose mode
- -D,
--debug-file=[debugfile]
- Write debug information to given file
- -V, --version
- Display version information and exit
- -h, --help
- Display help and exit
- -C,
--separator=[char]
- Separator for CSV created by 'list' operation (Default Value: ,)
- --delay=[seconds]
- Wait X seconds before fencing is started (Default Value: 0)
- --login-timeout=[seconds]
- Wait X seconds for cmd prompt after login (Default Value: 5)
- --power-timeout=[seconds]
- Test X seconds for status change after ON/OFF (Default Value: 20)
- --power-wait=[seconds]
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- --shell-timeout=[seconds]
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- --retry-on=[attempts]
- Count of attempts to retry power on (Default Value: 1)
- --ssh-path=[path]
- Path to ssh binary (Default Value: /usr/bin/ssh)
- --telnet-path=[path]
- Path to telnet binary (Default Value: /usr/bin/telnet)
- on
- Power on machine.
- off
- Power off machine.
- status
- This returns the status of the plug/virtual machine.
- list
- List available plugs with aliases/virtual machines if there is support for
more then one device. Returns N/A otherwise.
- list-status
- List available plugs with aliases/virtual machines and their power state
if it can be obtained without additional commands.
- monitor
- Check the health of fence device
- metadata
- Display the XML metadata describing this resource.
- manpage
-
The operational behavior of this is not known.
- validate-all
- Validate if all required parameters are entered.
- action
- Fencing action (Default Value: off)
- command_prompt
- Force Python regex for command prompt (Default Value: ['> '])
Obsoletes: cmd_prompt
- identity_file
- Identity file (private key) for SSH
- inet4_only
- Forces agent to use IPv4 addresses only
- inet6_only
- Forces agent to use IPv6 addresses only
- ip
- IP address or hostname of fencing device This parameter is always
required. Obsoletes: ipaddr
- ipport
- TCP/UDP port to use for connection with device (Default Value: 23)
- password
- Login password or passphrase Obsoletes: passwd
- password_script
- Script to run to retrieve password Obsoletes: passwd_script
- plug
- Physical plug number on device, UUID or identification of machine This
parameter is always required. Obsoletes: port
- ssh
- Use SSH connection Obsoletes: secure
- ssh_options
- SSH options to use
- username
- Login name This parameter is always required. Obsoletes: login
- quiet
- Disable logging to stderr. Does not affect --verbose or --debug-file or
logging to syslog.
- verbose
- Verbose mode
- debug_file
- Write debug information to given file Obsoletes: debug
- version
- Display version information and exit
- help
- Display help and exit
- separator
- Separator for CSV created by 'list' operation (Default Value: ,)
- delay
- Wait X seconds before fencing is started (Default Value: 0)
- login_timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- power_timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- power_wait
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- shell_timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- retry_on
- Count of attempts to retry power on (Default Value: 1)
- ssh_path
- Path to ssh binary (Default Value: /usr/bin/ssh)
- telnet_path
- Path to telnet binary (Default Value: /usr/bin/telnet)