fence_cisco_mds - Fence agent for Cisco MDS
fence_cisco_mds is an I/O Fencing agent which can be used with any
Cisco MDS 9000 series with SNMP enabled device.
fence_cisco_mds accepts options on the command line as well as
from stdin. Fenced sends parameters through stdin when it execs the agent.
fence_cisco_mds can be run by itself with command line options. This is
useful for testing and for turning outlets on or off from scripts.
Vendor URL: http://www.cisco.com
- -o,
--action=[action]
- Fencing action (Default Value: off)
- -c,
--community=[community]
- Set the community string
- -4, --inet4-only
- Forces agent to use IPv4 addresses only
- -6, --inet6-only
- Forces agent to use IPv6 addresses only
- -a, --ip=[ip]
- IP address or hostname of fencing device This parameter is always
required.
- -u,
--ipport=[port]
- TCP/UDP port to use for connection with device (Default Value: 161)
- -p,
--password=[password]
- Login password or passphrase
- -S,
--password-script=[script]
- Script to run to retrieve password
- -n, --plug=[id]
- Physical plug number on device, UUID or identification of machine This
parameter is always required.
- -b,
--snmp-auth-prot=[prot]
- Set authentication protocol (MD5|SHA)
- -P,
--snmp-priv-passwd=[pass]
- Set privacy protocol password
- -R,
--snmp-priv-passwd-script
- Script to run to retrieve privacy password
- -B,
--snmp-priv-prot=[prot]
- Set privacy protocol (DES|AES)
- -E,
--snmp-sec-level=[level]
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- -d,
--snmp-version=[version]
- Specifies SNMP version to use (1|2c|3)
- -l,
--username=[name]
- Login name
- -q, --quiet
- Disable logging to stderr. Does not affect --verbose or --debug-file or
logging to syslog.
- -v, --verbose
- Verbose mode
- -D,
--debug-file=[debugfile]
- Write debug information to given file
- -V, --version
- Display version information and exit
- -h, --help
- Display help and exit
- -C,
--separator=[char]
- Separator for CSV created by 'list' operation (Default Value: ,)
- --delay=[seconds]
- Wait X seconds before fencing is started (Default Value: 0)
- --login-timeout=[seconds]
- Wait X seconds for cmd prompt after login (Default Value: 5)
- --power-timeout=[seconds]
- Test X seconds for status change after ON/OFF (Default Value: 20)
- --power-wait=[seconds]
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- --shell-timeout=[seconds]
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- --retry-on=[attempts]
- Count of attempts to retry power on (Default Value: 1)
- --snmpget-path=[path]
- Path to snmpget binary (Default Value: /usr/bin/snmpget)
- --snmpset-path=[path]
- Path to snmpset binary (Default Value: /usr/bin/snmpset)
- --snmpwalk-path=[path]
- Path to snmpwalk binary (Default Value: /usr/bin/snmpwalk)
- on
- Power on machine.
- off
- Power off machine.
- status
- This returns the status of the plug/virtual machine.
- list
- List available plugs with aliases/virtual machines if there is support for
more then one device. Returns N/A otherwise.
- list-status
- List available plugs with aliases/virtual machines and their power state
if it can be obtained without additional commands.
- monitor
- Check the health of fence device
- metadata
- Display the XML metadata describing this resource.
- manpage
-
The operational behavior of this is not known.
- validate-all
- Validate if all required parameters are entered.
- action
- Fencing action (Default Value: off)
- Set the community string
- inet4_only
- Forces agent to use IPv4 addresses only
- inet6_only
- Forces agent to use IPv6 addresses only
- ip
- IP address or hostname of fencing device This parameter is always
required. Obsoletes: ipaddr
- ipport
- TCP/UDP port to use for connection with device (Default Value: 161)
- password
- Login password or passphrase Obsoletes: passwd
- password_script
- Script to run to retrieve password Obsoletes: passwd_script
- plug
- Physical plug number on device, UUID or identification of machine This
parameter is always required. Obsoletes: port
- snmp_auth_prot
- Set authentication protocol (MD5|SHA)
- snmp_priv_passwd
- Set privacy protocol password
- snmp_priv_passwd_script
- Script to run to retrieve privacy password
- snmp_priv_prot
- Set privacy protocol (DES|AES)
- snmp_sec_level
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- snmp_version
- Specifies SNMP version to use (1|2c|3)
- username
- Login name Obsoletes: login
- quiet
- Disable logging to stderr. Does not affect --verbose or --debug-file or
logging to syslog.
- verbose
- Verbose mode
- debug_file
- Write debug information to given file Obsoletes: debug
- version
- Display version information and exit
- help
- Display help and exit
- separator
- Separator for CSV created by 'list' operation (Default Value: ,)
- delay
- Wait X seconds before fencing is started (Default Value: 0)
- login_timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- power_timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- power_wait
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- shell_timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- retry_on
- Count of attempts to retry power on (Default Value: 1)
- snmpget_path
- Path to snmpget binary (Default Value: /usr/bin/snmpget)
- snmpset_path
- Path to snmpset binary (Default Value: /usr/bin/snmpset)
- snmpwalk_path
- Path to snmpwalk binary (Default Value: /usr/bin/snmpwalk)