fence_intelmodular - Fence agent for Intel Modular
fence_intelmodular is an I/O Fencing agent which can be used with
Intel Modular device (tested on Intel MFSYS25, should work with MFSYS35 as
well).
Note: Since firmware update version 2.7, SNMP v2 write support is
removed, and replaced by SNMP v3 support. So agent now has default SNMP
version 3. If you are using older firmware, please supply -d for command
line and snmp_version option for your cluster.conf.
fence_intelmodular accepts options on the command line as well as
from stdin. Fenced sends parameters through stdin when it execs the agent.
fence_intelmodular can be run by itself with command line options. This is
useful for testing and for turning outlets on or off from scripts.
Vendor URL: http://www.intel.com
- -o,
--action=[action]
- Fencing action (Default Value: reboot)
- -c,
--community=[community]
- Set the community string
- -4, --inet4-only
- Forces agent to use IPv4 addresses only
- -6, --inet6-only
- Forces agent to use IPv6 addresses only
- -a, --ip=[ip]
- IP address or hostname of fencing device This parameter is always
required.
- -u,
--ipport=[port]
- TCP/UDP port to use for connection with device (Default Value: 161)
- -p,
--password=[password]
- Login password or passphrase
- -S,
--password-script=[script]
- Script to run to retrieve password
- -n, --plug=[id]
- Physical plug number on device, UUID or identification of machine This
parameter is always required.
- -b,
--snmp-auth-prot=[prot]
- Set authentication protocol (MD5|SHA)
- -P,
--snmp-priv-passwd=[pass]
- Set privacy protocol password
- -R,
--snmp-priv-passwd-script
- Script to run to retrieve privacy password
- -B,
--snmp-priv-prot=[prot]
- Set privacy protocol (DES|AES)
- -E,
--snmp-sec-level=[level]
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- -d,
--snmp-version=[version]
- Specifies SNMP version to use (1|2c|3)
- -l,
--username=[name]
- Login name
- -q, --quiet
- Disable logging to stderr. Does not affect --verbose or --debug-file or
logging to syslog.
- -v, --verbose
- Verbose mode
- -D,
--debug-file=[debugfile]
- Write debug information to given file
- -V, --version
- Display version information and exit
- -h, --help
- Display help and exit
- -C,
--separator=[char]
- Separator for CSV created by 'list' operation (Default Value: ,)
- --delay=[seconds]
- Wait X seconds before fencing is started (Default Value: 0)
- --login-timeout=[seconds]
- Wait X seconds for cmd prompt after login (Default Value: 5)
- --power-timeout=[seconds]
- Test X seconds for status change after ON/OFF (Default Value: 20)
- --power-wait=[seconds]
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- --shell-timeout=[seconds]
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- --retry-on=[attempts]
- Count of attempts to retry power on (Default Value: 1)
- --snmpget-path=[path]
- Path to snmpget binary (Default Value: /usr/bin/snmpget)
- --snmpset-path=[path]
- Path to snmpset binary (Default Value: /usr/bin/snmpset)
- --snmpwalk-path=[path]
- Path to snmpwalk binary (Default Value: /usr/bin/snmpwalk)
- on
- Power on machine.
- off
- Power off machine.
- reboot
- Reboot machine.
- status
- This returns the status of the plug/virtual machine.
- list
- List available plugs with aliases/virtual machines if there is support for
more then one device. Returns N/A otherwise.
- list-status
- List available plugs with aliases/virtual machines and their power state
if it can be obtained without additional commands.
- monitor
- Check the health of fence device
- metadata
- Display the XML metadata describing this resource.
- manpage
-
The operational behavior of this is not known.
- validate-all
- Validate if all required parameters are entered.
- action
- Fencing action (Default Value: reboot)
- Set the community string
- inet4_only
- Forces agent to use IPv4 addresses only
- inet6_only
- Forces agent to use IPv6 addresses only
- ip
- IP address or hostname of fencing device This parameter is always
required. Obsoletes: ipaddr
- ipport
- TCP/UDP port to use for connection with device (Default Value: 161)
- password
- Login password or passphrase Obsoletes: passwd
- password_script
- Script to run to retrieve password Obsoletes: passwd_script
- plug
- Physical plug number on device, UUID or identification of machine This
parameter is always required. Obsoletes: port
- snmp_auth_prot
- Set authentication protocol (MD5|SHA)
- snmp_priv_passwd
- Set privacy protocol password
- snmp_priv_passwd_script
- Script to run to retrieve privacy password
- snmp_priv_prot
- Set privacy protocol (DES|AES)
- snmp_sec_level
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- snmp_version
- Specifies SNMP version to use (1|2c|3)
- username
- Login name Obsoletes: login
- quiet
- Disable logging to stderr. Does not affect --verbose or --debug-file or
logging to syslog.
- verbose
- Verbose mode
- debug_file
- Write debug information to given file Obsoletes: debug
- version
- Display version information and exit
- help
- Display help and exit
- separator
- Separator for CSV created by 'list' operation (Default Value: ,)
- delay
- Wait X seconds before fencing is started (Default Value: 0)
- login_timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- power_timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- power_wait
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- shell_timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- retry_on
- Count of attempts to retry power on (Default Value: 1)
- snmpget_path
- Path to snmpget binary (Default Value: /usr/bin/snmpget)
- snmpset_path
- Path to snmpset binary (Default Value: /usr/bin/snmpset)
- snmpwalk_path
- Path to snmpwalk binary (Default Value: /usr/bin/snmpwalk)