DOKK / manpages / debian 10 / powerstat / powerstat.8.en
POWERSTAT(8) System Manager's Manual POWERSTAT(8)

powerstat - a tool to measure power consumption

powerstat [options] [delay [count]]

powerstat measures the power consumption of a computer that has a battery power source or supports the RAPL (Running Average Power Limit) interface. The output is like vmstat but also shows power consumption statistics. At the end of a run, powerstat will calculate the average, standard deviation, minimum, maximum and geometic mean of the gathered data.

Note that running powerstat as root will provide extra information about process fork(2), exec(2) and exit(2) activity.

powerstat options are as follow:

enable all statistics gathering options, equivalent to -c, -f, -t and -H.
redo a sample measurement if a system is busy, the default for busy is considered less than 98% CPU idle. The CPU idle threshold can be altered using the -i option.
gather CPU C-state activity and show the % time and count in each C-state at the end of the run.
specify delay in seconds before starting, default is 180 seconds when running on battery or 0 seconds when using RAPL. This gives the machine time to settle down and for the battery readings to stabilize.
enable extra power stats showing all the power domain power readings. This currently only applies to the -R RAPL option.
compute an average frequency from all on-line CPU cores. Unfortunately a CPU core is always active to gather any form of stats because powerstat has to be running to do so, so these statistics are skewed by this. It is best to use this option with a reasonably large delay (more than 5 seconds) between samples to reduce the overhead of powerstat.
show GPU power readings. Currently just Intel i915 is supported and one needs to run powerstat with root privilege to access the kernel i915 /sys debug interface.
show help.
show histogram of power measurements.
specify the idle threshold (in % CPU idle) to force a re-sample measurement if the CPU is less idle than this level. This option implicitly enables the -b option.
no headings. Column headings are printed when they scroll off the terminal; this option disables this and allows one to capture the output and parse the data without the need to filter out the headings.
redo a sample measurement if any processes fork(), exec() or exit().
redo if system is not idle and any processes fork(), exec() or exit(), an alias for -p -b.
read power statistics from the RAPL (Running Average Power Limit) domains. This is supported by recent Linux kernels and Sandybridge and later Intel processors. This only covers some of the hardware in the machine, such as the processor package, DRAM controller, CPU core (power plane 0), graphics uncore (power plane 1) and so forth, so the readings do not cover the entire machine.
Because the RAPL readings are accurate and available immediately, the start delay (-d option) is defaulted to zero seconds.
this dumps a log of the process fork(), exec() and exit() activity on completion.
use standard averaging to calculate power consumption instead of using a 120 second rolling average of capacity samples. This is only useful if the battery reports just capacity values and is an alternative method of calculating the power consumption based on the start and current battery capacity.
gather temperatures from all the available thermal zones on the device. If there are no thermal zones available then nothing will be displayed.
forcibly ignore zero power rate readings from the battery. Use this to gather other statistics (for example when using -c, -f, -t options) if powerstat cannot measure power (not discharging or no RAPL interface).

Measure power with the default of 10 samples with an interval of 10 seconds

powerstat

Measure power with 60 samples with an interval of 1 second

powerstat 1 60

Measure power and redo sampling if we are not idle and we detect fork()/exec()/exit() activity

sudo powerstat -r

Measure power using the Intel RAPL interface:

powerstat -R

Measure power using the Intel RAPL interface and show extra RAPL domain power readings and power measurement histogram at end of the run

powerstat -RDH

Measure power and redo sampling if less that 95% idle

powerstat -i 95

Wait to settle for 1 minute then measure power every 20 seconds and show any fork()/exec()/exit() activity at end of the measuring

powerstat -d 60 -s 20

Measure temperature, CPU frequencies, C-states, power via RAPL domains, produce histograms, don't print repeated headings and measure every 0.5 seconds

powerstat -tfcRHn 0.5

vmstat(8), powertop(8), power-calibrate(8)

powerstat was written by Colin King <colin.king@canonical.com>

This manual page was written by Colin King <colin.king@canonical.com>, for the Ubuntu project (but may be used by others).

Copyright © 2011-2018 Canonical Ltd.
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

25 October 2017