| IBPORTSTATE(8) | Open IB Diagnostics | IBPORTSTATE(8) |
IBPORTSTATE - handle port (physical) state and link speed of an InfiniBand port
ibportstate [options] <dest dr_path|lid|guid> <portnum> [<op>]
ibportstate allows the port state and port physical state of an IB port to be queried (in addition to link width and speed being validated relative to the peer port when the port queried is a switch port), or a switch port to be disabled, enabled, or reset. InfiniBand HCA port state may be changed locally without the knowledge of the Subnet Manager. It also allows the link speed/width enabled on any IB port to be adjusted.
enable, disable, and reset change or reset a switch or HCA port state (You must specify the CA name and Port number when locally change CA port state.)
off change the port state to disable.
on change the port state to enable(only when the current state is disable).
speed and width are allowed on any port
speed values are the legal values for PortInfo:LinkSpeedEnabled (An error is indicated if PortInfo:LinkSpeedSupported does not support this setting)
espeed is allowed on any port supporting extended link speeds
fdr10 is allowed on any port supporting fdr10 (An error is indicated if port's capability mask indicates extended link speeds are not supported or if PortInfo:LinkSpeedExtSupported does not support this setting)
width values are legal values for PortInfo:LinkWidthEnabled (An error is indicated if PortInfo:LinkWidthSupported does not support this setting) (NOTE: Speed and width changes are not effected until the port goes through link renegotiation)
query also validates port characteristics (link width, speed, espeed, and fdr10) based on the peer port. This checking is done when the port queried is a switch port as it relies on combined routing (an initial LID route with directed routing to the peer) which can only be done on a switch. This peer port validation feature of query op requires LID routing to be functioning in the subnet.
mkey, mkeylease, and mkeyprot are only allowed on CAs, routers, or switch port 0 (An error is generated if attempted on external switch ports). Hexadecimal and octal mkeys may be specified by prepending the key with '0x' or '0', respectively. If a non-numeric value (like 'x') is specified for the mkey, then ibportstate will prompt for a value.
-L, --Lid The address specified is a LID
-G, --Guid The address specified is a Port GUID
-D, --Direct The address specified is a directed route
Examples:
[options] -D [options] "0" # self port
[options] -D [options] "0,1,2,1,4" # out via port 1, then 2, ...
(Note the second number in the path specified must match the port being
used. This can be specified using the port selection flag '-P' or the
port found through the automatic selection process.)
-s, --sm_port <smlid> use 'smlid' as the target lid for SA queries.
-C, --Ca <ca_name> use the specified ca_name.
-P, --Port <ca_port> use the specified ca_port.
Multiple port/Multiple CA support: when no IB device or port is specified (see the "local umad parameters" below), the libibumad library selects the port to use by the following criteria:
If a port and/or CA name is specified, the libibumad library attempts to fulfill the user request, and will fail if it is not possible.
For example:
ibaddr # use the first port (criteria #1 above) ibaddr -C mthca1 # pick the best port from "mthca1" only. ibaddr -P 2 # use the second (active/up) port from the first available IB device. ibaddr -C mthca0 -P 2 # use the specified port only.
--config, -z <config_file> Specify alternate config file.
-t, --timeout <timeout_ms> override the default timeout for the solicited mads.
-h, --help show the usage message
-V, --version show the version info.
/etc/infiniband-diags/ibdiag.conf
A global config file is provided to set some of the common options for all tools. See supplied config file for details.
| 2013-03-26 |