IPRCONFIG(8) | System Manager's Manual | IPRCONFIG(8) |
iprconfig - IBM Power RAID storage adapter configuration/recovery utility
iprconfig [-e editor] [-k dir] [-c command]
iprconfig --version --debug --force
iprconfig is used to configure IBM Power RAID storage adapters, display information about them, and to perform adapter and disk unit recovery. The menu options are:
1. Display hardware status.
This option can be used to display various information regarding the IBM Power
RAID adapters attached to the system and the disk units controlled by them.
For each adapter and disk unit, their /dev name, physical location,
description, vendor/product ID, and hardware status will be available.
Beside each resource is an OPT field. By entering a 1 beside any resource,
detailed information about that resource can be obtained. For an adapter
resource, this will display the adapter firmware version and the physical
location amongst other things.
2. Work with Disk Arrays
This option will present a second menu containing disk array related
commands.
Display disk array status is used to display the status of disk arrays on the system.
Create a disk array is used to create a disk array.
Delete a disk array is used to delete disk arrays. Selecting this option will provide you with a list of disk arrays which can be deleted.
Add a device to a disk array is used to include devices of similar capacity into an existing disk array. This function is currently only supported for RAID 5 and RAID 6 disk arrays.
Format device for advanced function is used to format disks to 522 bytes/sector so that they may be used in a disk array. Only disks which are not formatted for advanced function or are formatted for advanced function but are not known to be zeroed will be available for selection for this function.
Format device for JBOD function (512) is used to format disks to 512 bytes/sector so that they may be used as standalone disks. Only disks which are not formatted for JBOD function or are formatted for JBOD function and are in the Format Required state will be available for this function.
Work with hot spares is used to create a hot spare which designates a device as a dedicated hot spare. It is also used to delete a hot spare which unconfigures a previously configured hot spare.
Work with asymmetric access is used to select which path of a disk array will be the primary path in a dual controller environment. Asymmetric Access must be enabled on the adapter first. Not all adapters support asymmetric access and adapters that do provide support may require updated microcode.
Force RAID Consistency Check is used to force a consistency check on a RAID array. All ipr adapters continually perform background consistency checking when idle. This option can be used to force a consistency check to be performed.
Migrate disk array protection is used to change the RAID protection level for an array to another supported level. In some cases, this will require adding more disks to the array. In other cases, disks will be freed.
3. Work with disk unit recovery is used to perform the following disk unit recovery actions:
Concurrent add device is used to concurrently add a new disk to a running system. This feature is only supported with SES (SCSI Enclosure Services) packaging.
Concurrent remove device is used to concurrently remove a disk from a running system. This feature is only supported with SES (SCSI Enclosure Services) packaging.
Initialize and format disk unit is used to issue a SCSI format command to attached devices. A format unit command has special meaning to the adapter and is used as a service action for certain error conditions. Formatting a disk unit will lose all data on that drive. If the disk is attached to an ipr adapter that does not support RAID, the drive will be formatted to 512 bytes/sector. If the disk is attached to an ipr RAID adapter, the block size will not be changed. To change the block size, use the format menu options under the disk arrays menu.
Reclaim IOA cache storage is used to repair cache error conditions. ATTENTION: Use this option with care. This is used to discard data from the cache and may result in data loss. This option is designed to be used by authorized IBM hardware customer engineers.
Rebuild disk unit data is generally used following concurrent maintenance. Select this option after a failing array member device has been replaced to reconstruct the device as an active array member.
Work with resources containing cache battery packs is used to display information regarding rechargeable cache battery packs and to force rechargeable cache battery packs into an error state so that they can be replaced prior to failure. ATTENTION: Once an error has been forced on a rechargeable cache battery pack write caching will be disabled until the battery pack is replaced.
4. Work with SCSI bus configuration is used to change configurable SCSI bus attributes, such as maximum SCSI bus speed, SCSI initiator ID, etc.
5. Work with driver configuration is used to change driver configurable attributes, such as log_level.
6. Work with disk configuration is used to change configurable disk attributes, such as queue depth.
7. Work with adapter configuration is used to change configurable adapter attributes, such as dual adapter settings. Refer to the following command line options: primary, secondary, query-ha-mode, set-ha-mode, set-ioa-asymmetric-access and set-array-asymmetric-access for more information regarding these settings.
8. Download microcode is used to download microcode to ipr adapters and attached SCSI disks.
9. Analyze Log is an option available to analyze /var/log/messages* files. By default it will use vi as the editor to open the concatenated error log files. This can be changed by using option 6 on the Kernel Messages Log menu. Selecting option 1 on the Kernel Messages Log menu will display only the most recent errors logged by the ipr device driver and may be useful to filter out some of the clutter. Option 2 will display all recorded errors logged by the ipr device driver. Option 3 will display all kernel messages. Option 4 will display errors logged by the iprconfig utility. This may be useful for debugging problems. Option 5 can be used to change where the tool looks to find the kernel messages files. The default is to look in /var/log.
Brian King <brking@us.ibm.com>
Only use this utility across 5250 telnet when there are no other options available to you. Since there may be occasions when 5250 telnet is your only option to access your iSeries Linux console, every attempt has been made to make this utility usable under 5250 telnet. By following a few guidelines, you can make your 5250 telnet experience more productive and much less frustrating.
1. First of all, it will be helpful to know how the keys are mapped under 5250 telnet. From the 5250 telnet window, hit ESC. This will get you to the Send TELNET Control Functions menu. Take option 6 to display the keyboard map. Take note of how TAB, ESC, CTLC, and SENDWOCR are bound. They will be useful in the future.
2. When selecting menu options, enter the menu number, followed by the enter key, same as usual.
3. When typing single character commands (eg. r=Refresh), type the single character followed by the SENDWOCR key (F11 by default).
4. When on a device/array/IOA selection screen (eg. Display Disk Unit Details), do NOT use the arrow keys to navigate. Instead use the TAB key (F7 by default) to navigate these screens.
5. Beware of the backspace and delete keys. As a rule do NOT use them.
6. When editing the root kernel message log directory or the default editor, you may use the arrow keys, but not the backspace and delete keys. Use the space bar to remove already typed characters.
August 2009 |