| libnbd(3) | LIBNBD | libnbd(3) |
libnbd - network block device (NBD) client library in userspace
#include <libnbd.h>
struct nbd_handle *nbd;
char buf[512];
if ((nbd = nbd_create ()) == NULL ||
nbd_connect_tcp (nbd, "server.example.com", "nbd") == -1 ||
nbd_pread (nbd, buf, sizeof buf, 0, 0) == -1)
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
nbd_close (nbd);
cc prog.c -o prog -lnbd
or:
cc prog.c -o prog `pkg-config libnbd --cflags --libs`
Network Block Device (NBD) is a network protocol for accessing block devices over the network. Block devices are hard disks and things that behave like hard disks such as disk images and virtual machines.
Libnbd is a client library for the NBD protocol which can access most of the features of NBD while being simple to use and powerful.
This manual page gives an overview of libnbd, using C as an example, but the library is available from other programming languages.
To use the API at all you must first open a handle by calling nbd_create(3) (or its equivalent in other languages):
struct nbd_handle *nbd; nbd = nbd_create ();
This creates and returns a handle, which is associated with one connection to an NBD server, initially not connected.
Each handle is a complex state machine which can be in states such as created, connected to a remote server, handshaking, idle and ready to issue commands, or busy sending or receiving commands.
There are two levels of API available. A simple high level synchronous API lets you give the handle high level instructions like “connect to the server”, “read a block”, “write a block”, etc. Each of these functions will run to completion, blocking the current thread before returning. A more complicated low level non-blocking asynchronous API is also available where you can integrate with poll(2) or another main loop.
You can freely mix the two APIs on the same handle. You can also call APIs on a single handle from multiple threads. Single API calls on the handle are atomic — they either take a lock on the handle while they run or are careful to access handle fields atomically.
Libnbd does not create its own threads.
This is the simplest way to use the API, with the possible drawback that each libnbd function blocks until it is finished.
Create a handle and connect to the server:
struct nbd_handle *nbd;
nbd = nbd_create ();
if (!nbd) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
if (nbd_connect_tcp (nbd, "server.example.com", "nbd") == -1) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
Read the first sector (512 bytes) from the NBD export:
char buf[512];
if (nbd_pread (nbd, buf, sizeof buf, 0, 0) == -1) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
Close the handle:
nbd_close (nbd);
You can call the high level API from multiple threads, but each libnbd API call takes a lock on the handle and so commands will not run in parallel.
The low level API is useful if you want to use libnbd in non-blocking code; or if you want to issue commands in parallel from multiple threads; or if you need more control especially over having multiple commands in-flight on a single connection.
To use the low level API you will need to integrate with poll(2) or another “main loop” such as the GLib main event loop.
Use the "nbd_aio_*" variants to issue commands asynchronously (without waiting for the command to complete before returning). For example the asynchronous variant of nbd_pread(3) is:
int64_t cookie;
cookie = nbd_aio_pread (nbd, buf, sizeof buf,
NBD_NULL_COMPLETION, 0);
if (cookie == -1) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
There are several things to note here:
Each libnbd handle has an associated socket (once it has started connecting). You can read the file descriptor of the socket using:
int fd = nbd_aio_get_fd (nbd);
The socket is non-blocking. Between calls into libnbd it is in the "would block" condition. You can find out if libnbd is expecting to read or write from the socket next by calling:
int dir = nbd_aio_get_direction (nbd);
which returns one of "LIBNBD_AIO_DIRECTION_READ", "LIBNBD_AIO_DIRECTION_WRITE" or "LIBNBD_AIO_DIRECTION_BOTH" (= "READ|WRITE"). And so to set up the next call to poll(2) or other main loop you must translate this to "POLLIN", "POLLOUT" or "POLLIN|POLLOUT" (or whatever mechanism your main loop uses).
When you detect (eg. using poll(2)) that a read or write event has happened on the socket, you must then tell libnbd about it. You have to check the direction again (since it may have been changed by another thread), and notify libnbd:
int r = 0;
dir = nbd_aio_get_direction (nbd);
if ((dir & LIBNBD_AIO_DIRECTION_READ) &&
a_read_event_occurred ())
r = nbd_aio_notify_read (nbd);
else if ((dir & LIBNBD_AIO_DIRECTION_WRITE) &&
a_write_event_occurred ())
r = nbd_aio_notify_write (nbd);
if (r == -1) {
fprintf (stderr, "%s\n", nbd_get_error ());
// ...
}
The notify calls move the state machine along, reading and writing from the socket possibly multiple times, until the socket would block again, at which point they return control to the caller.
In fact if you want to use poll(2) on a single handle, a simple implementation has already been written called nbd_poll(3). It is also useful to examine how this is implemented (lib/poll.c in the libnbd source code) because that will tell you how to integrate libnbd with more complex main loops.
Some examples of using nbd_poll(3) follow.
As with the high level API, it all starts by creating a handle:
struct nbd_handle *nbd;
nbd = nbd_create ();
if (nbd == NULL) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
To connect to the server asynchronously, we start the connection using nbd_aio_connect(3) and then enter our main loop to check for events until the connection becomes ready:
int fd;
struct sockaddr_un addr;
socklen_t len;
/* some code to set up addr,
then ... */
if (nbd_aio_connect (nbd, &addr, len) == -1) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
while (! nbd_aio_is_ready (nbd)) {
if (nbd_poll (nbd, -1) == -1) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
}
To read data asynchronously, start an asynchronous read command, which returns a 64 bit command cookie, and enter the main loop until the command has completed:
int64_t cookie;
char buf[512];
cookie = nbd_aio_pread (nbd, buf, sizeof buf, offset,
NBD_NULL_COMPLETION, 0);
if (cookie == -1) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
while (! nbd_aio_command_completed (nbd, cookie)) {
if (nbd_poll (nbd, -1) == -1) {
fprintf (stderr, "%s\n", nbd_get_error ());
nbd_close (nbd);
exit (EXIT_FAILURE);
}
}
For almost all high level synchronous calls (eg. nbd_pread(3)) there is a low level asynchronous equivalent (eg. nbd_aio_pread(3)) for starting a command.
See https://github.com/libguestfs/libnbd/blob/master/examples/glib-main-loop.c
When any API call returns an error ("-1" or "NULL" depending on the API), an error message and sometimes an errno value are available. You can retrieve the error message and/or errno of the most recently failed call using nbd_get_error(3) and nbd_get_errno(3). For example:
if (nbd_connect_tcp (nbd, "remote", "nbd") == -1) {
fprintf (stderr,
"failed to connect to remote server: %s (errno = %d)\n",
nbd_get_error (), nbd_get_errno ());
}
These functions use thread-local storage to return the most recent error in the current thread. This is why you don't need to pass the handle to these calls. They even work if nbd_create(3) returns "NULL" when there is no handle at all.
For this reason you cannot call them from a different thread. You should call them immediately after the failed API call, from the same thread. Furthermore the error string returned by nbd_get_error(3) is only valid until the next libnbd API call in the current thread, so if you need to keep the string you must copy it (eg. using strdup(3)).
For some errors, a system call error number (see errno(3)) is available. You can find the error number by calling nbd_get_errno(3). It works the same way as nbd_get_error(3) with respect to threads.
Even when a call returns an error, nbd_get_errno(3) might return 0. This does not mean there was no error. It means no additional errno information is available for this error.
The error number is often the raw error returned by a system call that failed.
It can also be used to indicate special conditions. The most common cases are:
Libnbd can print lots of debugging messages, useful if you have a problem with the library. Either enable debugging after creating the handle:
nbd = nbd_create (); nbd_set_debug (nbd, true);
or set the "LIBNBD_DEBUG=1" environment variable which will enable debugging by default on all new handles.
Debugging messages are sent to stderr by default, but you can redirect them to a logging system using nbd_set_debug_callback(3).
There are several ways to connect to NBD servers, and you can even run a server from libnbd. Normally you would connect to a server which is already running, over a local Unix domain socket or a remote TCP connection. The high level API calls are:
nbd_connect_unix (nbd, "socket"); nbd_connect_tcp (nbd, "localhost", "nbd");
For nbd_connect_tcp(3) the third parameter is the port name or number, which can either be a name from /etc/services or the port number as a string (eg. "10809").
libnbd supports the NBD URI specification. The URIs that libnbd currently supports is documented in nbd_connect_uri(3).
You can connect to a URI as in these examples (using the high level API):
nbd_connect_uri (nbd, "nbd://example.com/"); nbd_connect_uri (nbd, "nbds+unix:///export?socket=/tmp/nbd.sock");
This feature is implemented by calling other libnbd APIs to set up the export name, TLS parameters, and finally connect over a Unix domain socket or TCP.
URI support is an optional feature of the library, requiring libxml2 at compile time. The nbd_connect_uri(3) and nbd_aio_connect_uri(3) calls will raise an error (with nbd_get_errno(3) returning "ENOTSUP") if it was not built with this feature, and you can also test for it explicitly using nbd_supports_uri(3).
Some NBD servers — notably nbdkit(1) with the -s parameter, and nbd-server(1) with the port parameter set to 0 — can also accept a single NBD connection on stdin/stdout. You can run these servers as a subprocess of your main program using nbd_connect_command(3). This example creates a 1G writable RAM disk:
char *argv[] = { "nbdkit", "-s", "--exit-with-parent",
"memory", "1G", NULL };
nbd_connect_command (nbd, argv);
When the handle is closed the nbdkit subprocess is killed, which in this case means the RAM disk is discarded, so this is useful for testing.
Some NBD servers — notably nbdkit(1) and qemu-nbd(1) — support systemd socket activation allowing libnbd to pass a socket to the subprocess. This works very similarly to nbd_connect_command(3) described above, but you must use nbd_connect_systemd_socket_activation(3) instead.
By default, when beginning a connection, libnbd will handle all negotiation with the server, using only the configuration (eg. nbd_set_export_name(3) or nbd_add_meta_context(3)) that was requested before the connection attempt; this phase continues until nbd_aio_is_connecting(3) no longer returns true, at which point, either data commands are ready to use or else the connection has failed with an error.
But there are scenarios in which it is useful to also control the handshaking commands sent during negotiation, such as asking the server for a list of available exports prior to selecting which one to use. This is done by calling nbd_set_opt_mode(3) before connecting; then after requesting a connection, the state machine will pause at nbd_aio_is_negotiating(3) at any point that the user can decide which handshake command to send next. Note that the negotiation state is only reachable from newstyle servers; older servers cannot negotiate and will progress all the way to the ready state.
When the negotiating state is reached, you can initiate option commands such as nbd_opt_list(3) or their asynchronous equivalents, as well as alter configuration such as export name that previously had to be set before connection. Since the NBD protocol does not allow parallel negotiating commands, no cookie is involved, and you can track completion of each command when the state is no longer nbd_aio_is_connecting(3). If nbd_opt_go(3) fails but the connection is still live, you will be back in negotiation state, where you can request a different export name and try again. Exiting the negotiation state is only possible with a successful nbd_opt_go(3) which moves to the data phase, or nbd_opt_abort(3) which performs a clean shutdown of the connection by skipping the data phase.
It is possible for NBD servers to serve different content on different “exports”. For this you must pass the right export name to the server. Call this API before connecting:
nbd_set_export_name (nbd, "export");
Note that there are some servers (like nbdkit(1) ≤ 1.14) which ignore this, and other servers (like qemu-nbd(8)) which require it to be set correctly but cannot serve different content.
These APIs are also available after a successful nbd_opt_info(3) during the negotiation phase, if you used nbd_set_opt_mode(3) prior to connecting.
After connecting the server will send back a set of flags describing the export, such as whether it is writable and if it can support flush to permanent storage. These flags can be accessed from libnbd using APIs such as:
int is_read_only = nbd_is_read_only (nbd); int can_flush = nbd_can_flush (nbd);
Flag calls are: nbd_can_cache(3), nbd_can_df(3), nbd_can_fast_zero(3), nbd_can_flush(3), nbd_can_fua(3), nbd_can_meta_context(3), nbd_can_multi_conn(3), nbd_can_trim(3), nbd_can_zero(3), nbd_is_read_only(3), nbd_is_rotational(3).
To get the size of the export in bytes, use nbd_get_size(3):
int64_t size = nbd_get_size (nbd);
You can read and write data from the NBD server using nbd_pread(3) and nbd_pwrite(3) or their asynchronous equivalents.
All data commands support a "flags" argument (mandatory in C, but optional in languages where it can default to 0). For convenience, the constant "LIBNBD_CMD_FLAG_MASK" is defined with the set of flags currently recognized by libnbd, where future NBD protocol extensions may result in additional flags being supported; but in general, specific data commands only accept a subset of known flags.
Libnbd defaults to performing some client-side sanity checking in each of its data commands; for example, attempts to write to a server that has advertised a read-only connection are rejected. It is possible to override aspects of this checking by using nbd_set_strict_mode(3).
Some servers also support:
This is slightly different from trimming because the backing storage is still allocated. For some storage types this can make future writes more efficient and/or less likely to fail because of out of space errors.
The nbd_flush(3) call (available if nbd_can_flush(3) returns true) flushes all pending writes to disk and does not complete until that operation has finished. It is similar to using sync(2) on POSIX systems.
A more efficient way to achieve this is to set the flag "LIBNBD_CMD_FLAG_FUA" on write-like calls (like write, trim and zero). This flag means the call will not complete until committed to permanent storage, but it does not involve flushing the entire disk.
In order to utilize block status, the client must call nbd_add_meta_context(3) prior to connecting, for each meta context in which it is interested, then check nbd_can_meta_context(3) after connection to see which contexts the server actually supports. If a context is supported, the client can then use nbd_block_status(3) with a callback function that will receive an array of 32-bit integer pairs describing consecutive extents within a context. In each pair, the first integer is the length of the extent, the second is a bitmask description of that extent (for the "base:allocation" context, the bitmask may include "LIBNBD_STATE_HOLE" for unallocated portions of the file, and/or "LIBNBD_STATE_ZERO" for portions of the file known to read as zero).
There is a full example of requesting meta context and using block status available at https://github.com/libguestfs/libnbd/blob/master/interop/dirty-bitmap.c
NBD servers which properly implement the specification can handle multiple data requests in flight over the same connection at the same time. Libnbd supports this when using the low level API.
To use it you simply issue more requests as needed (eg. using calls like nbd_aio_pread(3), nbd_aio_pwrite(3)) without waiting for previous commands to complete. You need to be careful that requests in flight do not overlap with disk offsets of other write-like commands in flight — an overlapping read may see indeterminate data, and an overlapping write may even cause disk corruption where the resulting disk contents do not match either of the two writes.
Each request is identified by a unique 64 bit cookie (assigned by libnbd), allowing libnbd and callers to match replies to requests. Replies may arrive out of order. A request that is rejected client-side for failing a sanity check (such as attempting to write to a read-only server, see nbd_set_strict_mode(3)) will fail rather than returning a cookie, although closure cleanup is still performed.
Although in theory you can have an indefinite number of requests in flight at the same time, in practice it's a good idea to limit them to some number. Libnbd will queue commands in the handle even if it cannot write them to the server, so this limit is largely to prevent a backlog of commands from consuming too much memory. It is suggested to start with a limit of 64 requests in flight (per NBD connection), and measure how adjusting the limit up and down affects performance for your local configuration.
There is a full example using multiple in-flight requests available at https://github.com/libguestfs/libnbd/blob/master/examples/threaded-reads-and-writes.c
Some NBD servers advertise “multi-conn” which means that it is safe to make multiple connections to the server and load-balance commands across all of the connections.
To do this you should open a single connection first and test for this feature using nbd_can_multi_conn(3). Without error handling it would look like this:
struct nbd_handle *nbd[4]; size_t i; bool supports_multi_conn; nbd[0] = nbd_create (); nbd_connect_tcp (nbd[0], "server", "10809"); supports_multi_conn = nbd_can_multi_conn (nbd[0]) > 0;
If multi-conn is supported then you can open further connections:
if (supports_multi_conn) {
for (i = 1; i <= 3; ++i) {
nbd[i] = nbd_create ();
nbd_connect_tcp (nbd[i], "server", "10809");
}
}
If you are issuing multiple in-flight requests (see above) and limiting the number, then the limit should be applied to each individual NBD connection.
The NBD protocol and libnbd supports TLS (sometimes incorrectly called “SSL”) for encryption of the data stream and authentication of clients and servers. Libnbd defaults to TLS disabled for maximum interoperability. To enable it on a handle you must call nbd_set_tls(3) before connecting.
To allow TLS, but fall back to unencrypted:
nbd_set_tls (nbd, LIBNBD_TLS_ALLOW);
Use nbd_get_tls_negotiated(3) to find out if TLS negotiation was successful. Avoid "LIBNBD_TLS_ALLOW" if man-in-the-middle attacks are a concern.
The most secure mode is to require TLS and fail to connect if the server does not support it:
nbd_set_tls (nbd, LIBNBD_TLS_REQUIRE);
It may also be necessary to verify that the server’s identity is correct. For some servers it may be necessary to verify to the server that the client is permitted to connect. This can be done using either X.509 certificates, or TLS Pre-Shared Keys (PSK). Certificates are more secure. PSK is far more convenient, but you must have an existing secure channel to distribute the keys.
This is the default if you don’t call any other "nbd_set_tls_*" functions. In this case the server must have a public (eg. HTTPS) certificate which can be verified against the CAs registered on your system (eg. under /etc/pki).
To disable server name verification — which opens you up to a potential Man-In-The-Middle (MITM) attack — use:
nbd_set_tls_verify_peer (nbd, false);
You can set up your own CA and register clients and servers with it, issuing client and server certificates which will reliably authenticate your clients and servers to each other.
Doing this is described in detail in the nbdkit-tls(1) manual. The only differences for libnbd are:
Once you have set up the directory containing the certificates, call:
nbd_set_tls_certificates (nbd, "/path/to/directory");
TLS Pre-Shared Keys are a much more convenient method of setting up TLS, and more appropriate for NBD, but you should have an existing secure method available to distribute the keys. They are therefore ideal if you want to set up an NBD service as an adjunct to an existing secure REST API.
Use psktool(1) to create a file of "username:key" pairs:
psktool -u username -p keys.psk
and pass this path to libnbd:
nbd_set_tls_psk_file (nbd, "keys.psk");
If necessary you may need to set the client username (otherwise libnbd will use your login name):
nbd_set_tls_username (nbd, "username");
Some libnbd calls take callbacks (eg. nbd_set_debug_callback(3), nbd_aio_pread(3)). Libnbd can call these functions while processing.
In the C API these libnbd calls take a structure which contains the function pointer and an optional opaque "void *user_data" pointer:
nbd_aio_pread (nbd, buf, sizeof buf, offset,
(nbd_completion_callback) { .callback = my_fn,
.user_data = my_data },
0);
For optional callbacks, if you don't want the callback, either set ".callback" to "NULL" or use the equivalent macros (such as "NBD_NULL_COMPLETION") defined in "libnbd.h":
nbd_aio_pread (nbd, buf, sizeof buf, offset,
NBD_NULL_COMPLETION, 0);
From other languages the structure and opaque pointer are not needed because you can use closures to achieve the same effect.
You can associate an optional free function with callbacks. Libnbd will call this function when the callback will not be called again by libnbd, including in the case where the API fails.
This can be used to free associated "user_data". For example:
void *my_data = malloc (...);
nbd_aio_pread_structured (nbd, buf, sizeof buf, offset,
(nbd_chunk_callback) { .callback = my_fn,
.user_data = my_data,
.free = free },
NBD_NULL_CALLBACK(completion),
0);
will call free(3) on "my_data" after the last time that the "chunk.callback = my_fn" function is called.
The free function is only accessible in the C API as it is not needed in garbage collected programming languages.
It is possible to register a callback like this:
...
(nbd_completion_callback) { .callback = NULL,
.user_data = my_data,
.free = free },
...
The meaning of this is that the callback is never called, but the free function is still called after the last time the callback would have been called. This is useful for applying generic freeing actions when asynchronous commands are retired.
The callbacks are invoked at a point where the libnbd lock is held; as such, it is unsafe for the callback to call any "nbd_*" APIs on the same nbd object, as it would cause deadlock.
All of the low-level commands have a completion callback variant that registers a callback function used right before the command is marked complete.
When the completion callback returns 1, the command is automatically retired (there is no need to call nbd_aio_command_completed(3)); for any other return value, the command still needs to be retired.
Some of the high-level commands (nbd_pread_structured(3), nbd_block_status(3)) involve the use of a callback function invoked by the state machine at appropriate points in the server's reply before the overall command is complete. These callback functions, along with all of the completion callbacks, include a parameter "error" containing the value of any error detected so far; if the callback function fails, it should assign back into "error" and return "-1" to change the resulting error of the overall command. Assignments into "error" are ignored for any other return value; similarly, assigning 0 into "error" does not have an effect.
On most systems, C programs that use libnbd can be compiled like this:
cc prog.c -o prog -lnbd
To detect if the libnbd library and header file is installed, the preferred method is to use pkg-config(1) or pkgconf(1):
pkg-config libnbd --exists || fail libnbd is required
In case the library or header file are not installed in the usual system locations, you can compile your program like this, using pkg-config to detect the proper location of libnbd:
cc prog.c -o prog `pkg-config libnbd --cflags --libs`
External projects which use autoconf and need to check if libnbd is installed should use the "PKG_CHECK_MODULES" macro in configure.ac like this:
PKG_CHECK_MODULES([LIBNBD], [libnbd])
This will define "@LIBNBD_CFLAGS@" and "@LIBNBD_LIBS@" which you will need to add to your Makefile.am.
For CMake projects use:
find_package(PkgConfig REQUIRED)
pkg_check_modules(LIBNBD REQUIRED libnbd)
target_link_libraries(prog ${LIBNBD_LIBRARIES})
target_include_directories(prog PUBLIC ${LIBNBD_INCLUDE_DIRS})
target_compile_options(prog PUBLIC ${LIBNBD_CFLAGS_OTHER})
To compile an external project against a built copy of the libnbd source tree which hasn't been installed, see the ./run script.
nbd_add_meta_context(3), nbd_aio_block_status(3), nbd_aio_cache(3), nbd_aio_command_completed(3), nbd_aio_connect(3), nbd_aio_connect_command(3), nbd_aio_connect_socket(3), nbd_aio_connect_systemd_socket_activation(3), nbd_aio_connect_tcp(3), nbd_aio_connect_unix(3), nbd_aio_connect_uri(3), nbd_aio_connect_vsock(3), nbd_aio_disconnect(3), nbd_aio_flush(3), nbd_aio_get_direction(3), nbd_aio_get_fd(3), nbd_aio_in_flight(3), nbd_aio_is_closed(3), nbd_aio_is_connecting(3), nbd_aio_is_created(3), nbd_aio_is_dead(3), nbd_aio_is_negotiating(3), nbd_aio_is_processing(3), nbd_aio_is_ready(3), nbd_aio_notify_read(3), nbd_aio_notify_write(3), nbd_aio_opt_abort(3), nbd_aio_opt_go(3), nbd_aio_opt_info(3), nbd_aio_opt_list(3), nbd_aio_opt_list_meta_context(3), nbd_aio_peek_command_completed(3), nbd_aio_pread(3), nbd_aio_pread_structured(3), nbd_aio_pwrite(3), nbd_aio_trim(3), nbd_aio_zero(3), nbd_block_status(3), nbd_cache(3), nbd_can_cache(3), nbd_can_df(3), nbd_can_fast_zero(3), nbd_can_flush(3), nbd_can_fua(3), nbd_can_meta_context(3), nbd_can_multi_conn(3), nbd_can_trim(3), nbd_can_zero(3), nbd_clear_debug_callback(3), nbd_clear_meta_contexts(3), nbd_close(3), nbd_connect_command(3), nbd_connect_socket(3), nbd_connect_systemd_socket_activation(3), nbd_connect_tcp(3), nbd_connect_unix(3), nbd_connect_uri(3), nbd_connect_vsock(3), nbd_connection_state(3), nbd_create(3), nbd_flush(3), nbd_get_block_size(3), nbd_get_canonical_export_name(3), nbd_get_debug(3), nbd_get_errno(3), nbd_get_error(3), nbd_get_export_description(3), nbd_get_export_name(3), nbd_get_full_info(3), nbd_get_handle_name(3), nbd_get_handshake_flags(3), nbd_get_meta_context(3), nbd_get_nr_meta_contexts(3), nbd_get_opt_mode(3), nbd_get_package_name(3), nbd_get_protocol(3), nbd_get_request_structured_replies(3), nbd_get_size(3), nbd_get_strict_mode(3), nbd_get_structured_replies_negotiated(3), nbd_get_tls(3), nbd_get_tls_negotiated(3), nbd_get_tls_username(3), nbd_get_tls_verify_peer(3), nbd_get_version(3), nbd_is_read_only(3), nbd_is_rotational(3), nbd_kill_subprocess(3), nbd_opt_abort(3), nbd_opt_go(3), nbd_opt_info(3), nbd_opt_list(3), nbd_opt_list_meta_context(3), nbd_poll(3), nbd_pread(3), nbd_pread_structured(3), nbd_pwrite(3), nbd_set_debug(3), nbd_set_debug_callback(3), nbd_set_export_name(3), nbd_set_full_info(3), nbd_set_handle_name(3), nbd_set_handshake_flags(3), nbd_set_opt_mode(3), nbd_set_request_structured_replies(3), nbd_set_strict_mode(3), nbd_set_tls(3), nbd_set_tls_certificates(3), nbd_set_tls_psk_file(3), nbd_set_tls_username(3), nbd_set_tls_verify_peer(3), nbd_set_uri_allow_local_file(3), nbd_set_uri_allow_tls(3), nbd_set_uri_allow_transports(3), nbd_shutdown(3), nbd_supports_tls(3), nbd_supports_uri(3), nbd_trim(3), nbd_zero(3).
https://github.com/NetworkBlockDevice/nbd/blob/master/doc/proto.md, https://github.com/NetworkBlockDevice/nbd/blob/master/doc/uri.md.
libnbd-release-notes-1.6(1), libnbd-release-notes-1.4(1), libnbd-release-notes-1.2(1), libnbd-security(3), nbdcopy(1), nbdfuse(1), nbdinfo(1), nbdsh(1), qemu(1).
Eric Blake
Richard W.M. Jones
Copyright (C) 2019-2020 Red Hat Inc.
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
| 2021-02-09 | libnbd-1.6.1 |