Streamlines - Utility for plotting a streamline representation of
field flow data given two arrays containing the vector field components on a
uniform grid.
The following two calls are the minimum required to create a
streamline field flow plot using the current interface:
- STINIT - Performs initialization tasks required before STREAM may be
called to create a streamline field flow plot. Information about the input
data arrays is copied into internal common block variables and the
coordinate system mappings and boundaries are established.
- STREAM - Plots a streamline representation of field flow data, based on
conditions established by STINIT and the current values of a set of
user-modifiable internal parameters associated with the Streamlines
utility.
All user-modifiable internal parameters have default values; only
those which are to have values different from the default need to be set.
The routines used to set Streamlines parameters are as follows:
- STRSET - Resets all parameters to their initial default values.
- STSETI - Sets the value of an internal parameter of type INTEGER.
- STSETR - Sets the value of an internal parameter of type REAL.
In general, once a parameter is given a value by a call to one of
these routines, it retains that value until a similar call resets it.
Retrieve the value of an internal parameter by calling one of the following
routines:
- STGETI - Gets the current value of an internal parameter of type
INTEGER.
- STGETR - Gets the current value of an internal parameter of type
REAL.
Streamlines supports two obsolete routines for compatibility with
old NCAR Graphics codes. The compatibility mode parameter, CPM, offers a
number of options that allow considerable flexibility in making the
transition to the new version of the utility. When writing new code you are
encouraged not to use these entry points, since they provide less capability
than the standard Streamlines interface, and may eventually be phased
out.
- STRMLN - The principal entry point prior to Version 3.2, now a front end
to the STINIT/STREAM interface.
- EZSTRM - Front end to STRMLN: a simpler interface for standard situations,
when detailed control of the plot is not required.
c_stinit
c_stream
c_strset
c_stseti
c_stsetr
c_stgeti
c_stgetr
c_strmln
c_ezstrm
The following routines are not to be called directly. However, you
may modify them in order to customize the behavior of Streamlines. Three
routines (STUMXY, STUIXY, and STUMTA) are provided to support user-defined
mapping transformations. The fourth (STUMSL) allows you to tailor streamline
masking to your requirements.
- STUIXY - User modifiable routine that inversely maps a single point on the
streamline from user to data coordinate space.
- STUMSL - Default name for a user-definable external subroutine used to
draw masked streamlines. The default version of the routine draws any
polyline all of whose area identifiers are greater than or equal to
zero.
- STUMTA - Given the coordinates of a point on the streamline in data, user,
and NDC space, and the interpolated, normalized components of the vector
at the point relative to data coordinate space, the user-modifiable
routine STUMTA finds the directional angle of the streamline relative to
NDC space at the point.
- STUMXY - User modifiable routine that maps a single point on the
streamline from data to user coordinate space.
To use Streamlines, load the NCAR Graphics libraries ncarg,
ncarg_gks, and ncarg_c, preferably in that order.
In this section are listed, in alphabetical order, all the error
messages that may be written by Streamlines. Each error message begins with
the name of the Streamlines routine in which an error has been detected,
followed by a dash, followed by the error message itself. These error
messages are written by a call to the error-handling support routine SETER,
with a final argument indicating that the error is fatal and that execution
should be terminated.
- STGETI OR STGETR -
PARAMETER NAME NOT KNOWN - x
- The given parameter name (´x´) is not a legal parameter name
known to Streamlines.
- STGETI OR STGETR -
PARAMETER NAME TOO SHORT - x
- The parameter name ("x") is less than three characters
long.
- STINIT - U AND/OR V ARRAY
DIMENSIONS EXCEEDED
- The STINIT input argument, M, specifying the number of array elements to
use along the first dimension of the U and V arrays, exceeds the actual
first dimension of U and/or V, as specified by the input arguments LU and
LV.
- STREAM - TOO MANY AREA
GROUPS
- The area map passed as the argument, IAM, to STREAM contains more area
groups than allowed by the Streamlines utility, currently 64. This error
can occur only if the mask to area map parameter, MSK, has a value greater
than 0, specifying that streamlines are to be drawn masked to an area
map.
- STREAM - INVALID AREA
MAP
- The area map passed as the argument, IAM, to STREAM is judged to be
invalid because it contains a negative value for the number of area
groups. This error can occur only if the mask to area map parameter, MSK,
has a value greater than 0, specifying that streamlines are to be drawn
masked to an area map.
- STSETI OR STSETR -
PARAMETER NAME NOT KNOWN - x
- The given parameter name (´x´) is not a legal parameter name
known to Streamlines.
- STSETI OR STSETR -
PARAMETER NAME TOO SHORT - x
- The parameter name ("x") is less than three characters
long.
- STSETI OR STSETR -
PARAMETER VALUE OUT OF RANGE - x
- An attempt has been made to set the parameter named ´x´ to a
value outside the range allowed by the Streamlines utility.
Online: stgetc, stgeti, stgetr, stinit, stream,
streamlines_params, strset, stsetc, stseti, stsetr, stuixy, stumsl, stumta,
stumxy, ncarg_cbind.
Hardcopy: NCAR Graphics Fundamentals, UNIX Version
Copyright (C) 1987-2009
University Corporation for Atmospheric Research
The use of this Software is governed by a License Agreement.