DOKK / manpages / debian 11 / montage / mProjectPP.1.en
MPROJECTPP(1) Montage MPROJECTPP(1)

mProjectPP - Re-project FITS images

mProjectPP [-z factor] [-d level] [-b border] [-s statusfile] [-o altout.hdr] [-i altin.hdr] [-h hdu] [-x scale] [-w weightfile] [-W fixed-weight] [-t threshold] [-X] [-b border-string] in.fits out.fits template.hdr

mProjectPP reprojects a single image to the scale defined in an alternate FITS header template generated (usually) by mTANhdr. The program produces a pair of images: the reprojected image and an "area" image consisting of the fraction input pixel sky area that went into each output pixel. This area image goes through all the subsequent processing that the reprojected image does, allowing it to be properly coadded at the end.

mProjectPP performs a plane-to-plane transform on the input image, and is an adaptation of the Mopex algorithm and developed in collaboration with the Spitzer Space Telescope. It provides a speed increase of approximately a factor of 30 over the general-purpose mProject. However, mProjectPP is only suitable for projections which can be approximated by tangent-plane projections (TAN, SIN, ZEA, STG, ARC), and is therefore not suited for images covering large portions of the sky. Also note that it does not directly support changes in coordinate system (i.e. equatorial to galactic coordinates), though these changes can be facilitated by the use of an alternate header.

One situation that has happened often enough to warrant special note: It is possible to define a FITS header with the reference location off the image. In particular, people often reference cylindrical projections (e.g., CAR, CEA) to location (0.,0.) (e.g., the Galactic center). This is not wrong in itself but does lead to extremely large pixel offsets (e.g., in the hundreds of thousands). Related to this, if you extract a header from an image with large offsets of this type, it is unlikely that you can simply change projection types without also adjusting the reference location/offsets. Most likely, you will end up with the reproject data all being off-scale.

Processing is done utilizing the drizzle algorithm. factor is a floating point number; recommended drizzle factors are from 0.5 to 1.
Causes additional debugging information to be printed to stdout. Valid levels are 1-5; for levels greater than 1, it's recommended to redirect the output into a text file.
Ignores border pixels around the image edge when performing calculations.
Output and errors are written to statusfile instead of being written to stdout.
-[i|o] alternate.hdr
Specifies an alternate FITS header for use in mProjectPP calculations, allows substitution of psuedo-TAN headers created by mTANHdr.
Specify the FITS extension to re-project if the FITS image is multi-extension.
Multiple the pixel values by scale when reprojecting. For instance, each 2MASS image has a different scale factor (very near 1.0) to correct for varying magnitude-zero points.
Path to a weight map to be used when reading values from the input image.
Use constant weight value for the whole image.
Pixels with weights below threshold will be treated as blank.
Makes the output region (originally defined in the header template) big enough to include all of the input images
Define a border width or border pixel corners outside of which all pixels are set to NaN.

Input FITS file to be reprojected.
Path to output FITS file to be created.
FITS header template to be used in generation of output FITS

Two files are created as output: the reprojected FITS file (out.fits), and an "area" image (out_area.fits). See the image reprojection algorithm for more information.

[struct stat="OK", time=seconds]
Drizzle factor string (string) cannot be interpreted as a real number
Cannot open status file: statusfile
Weight threshold string (threshold) cannot be interpreted as a real number
Flux scale string (scale) cannot be interpreted as a real number
Border value string (string) cannot be interprted as an integer or a set of polygon vertices
Border value (value) must be greater than or equal to zero
HDU value (hdu) must be a non-negative integer
Could not set up plane-to-plane transform. Check for compliant headers.
No overlap
Not enough memory for output data image array
Not enough memory for output area image array
Output wcsinit() failed.
Input wcsinit() failed.
Input and output must be in the same coordinate system for fast reprojection
All pixels are blank
Input image projection (projection) must be TAN, SIN, ZEA, STG or ARC for fast reprojection
Output image projection (projection) must be TAN, SIN, ZEA, STG or ARC for fast reprojection
Template file [template.hdr] not found
Image file in.fits is missing or invalid FITS
Weight file weightfile is missing or invalid FITS
FITS library error

$ mProjectPP rawdir/real_orig.fits projdir/base_unity.fits templates/galactic_orig.txt
[struct stat="OK", time=14]

The drizzle algorithm has been implemented but has not been tested in this release.

If a header template contains carriage returns (i.e., created/modified on a Windows machine), the cfitsio library will be unable to read it properly, resulting in the error: [struct stat="ERROR", status=207, msg="illegal character in keyword"]

It is best for the background correction algorithms if the area described in the header template completely encloses all of the input images in their entirety. If parts of input images are "chopped off" by the header template, the background correction will be affected. We recommend you use an expanded header for the reprojection and background modeling steps, returning to the originally desired header size for the final coaddition. The default background matching assumes that there are no non-linear background variations in the individual images (and therefore in the overlap differences). If there is any uncertainty in this regard, it is safer to turn on the "level only" background matching (the "-l" flag in mBgModel.

mProjectPP is only suitable for use on projections which can be approximated by tangent-plane projections (TAN, SIN, ZEA, STG, ARC), and is therefore not suited for images covering large portions of the sky. Also note that it does not directly support changes in coordinate system (i.e. equatorial to galactic coordinates), though these changes can be facilitated by the use of an alternate header.

2001-2015 California Institute of Technology, Pasadena, California

If your research uses Montage, please include the following acknowledgement: "This research made use of Montage. It is funded by the National Science Foundation under Grant Number ACI-1440620, and was previously funded by the National Aeronautics and Space Administration's Earth Science Technology Office, Computation Technologies Project, under Cooperative Agreement Number NCC5-626 between NASA and the California Institute of Technology."

The Montage distribution includes an adaptation of the MOPEX algorithm developed at the Spitzer Science Center.

Dec 2016 Montage 5