DOKK / manpages / debian 11 / nbdkit / nbdkit-ip-filter.1.en
nbdkit-ip-filter(1) NBDKIT nbdkit-ip-filter(1)

nbdkit-ip-filter - filter clients by IP address, process ID, user ID or group ID

 nbdkit --filter=ip PLUGIN [allow=addr[,addr...]]
                           [deny=addr[,addr...]]

"nbdkit-ip-filter" can allow or deny client connections by their IP address. Usually it is better to control this outside nbdkit, for example using TCP wrappers or a firewall, but this filter can be used if these are not available.

nbdkit ≥ 1.24 added the ability to filter clients connecting over Unix domain sockets by client process ID, user ID and group ID. Also this version added support for filtering "AF_VSOCK" sockets by peer CID or port.

 nbdkit --filter=ip [...] allow=127.0.0.1,::1 deny=all

Allow clients to connect on the loopback IPv4 or loopback IPv6 address, deny all other clients.

 nbdkit --filter=ip [...] deny=8.0.0.0/8

Allow any client except connections from the IPv4 "8.0.0.0/8" network.

 nbdkit --filter=ip [...] allow=anyipv6 deny=all

Allow IPv6 clients to connect from anywhere, deny all other sources.

 nbdkit -U $tmpdir/sock --filter=ip [...] allow=uid:`id -u` deny=all

Only allow the current user ("id -u") to connect over the socket.

Layer extra security by creating the socket inside a temporary directory only accessible by the user.

 nbdkit -U $tmpdir/sock --filter=ip [...] allow=gid:`id -g` deny=all

Allow anyone in the same group as the current user to connect to the Unix domain socket.

As in the previous example, layer extra security by creating the socket inside a temporary directory only accessible by the group.

When a client connects, this filter checks its source address against the allow and deny lists as follows:

1.
If the address matches any in the allow list, permission is granted.
2.
If the address matches any in the deny list, permission is denied.
3.
Otherwise permission is granted.

If either the "allow" or "deny" parameter is not present then it is assumed to be an empty list. The order in which the parameters appear on the command line does not matter; the allow list is always processed first and the deny list second.

The "allow" and "deny" parameters each contain a comma-separated list of any of the following:

These keywords (which both have the same meaning) match any source.
These keywords match any IPv4 address.
These keywords match any IPv6 address.
These keywords match any connection over a Unix domain socket.
These keywords match any connection over an "AF_VSOCK" socket.
This matches the single IPv4 address "A.B.C.D", for example 127.0.0.1.
This matches the range of IPv4 addresses "A.B.C.D/NN", for example "192.168.2.0/24" or "10.0.0.0/8".
This matches the single IPv6 address "A:B:...". The usual IPv6 address representations can be used (see RFC 5952).
This matches a range of IPv6 addresses "A:B:.../NN".
(nbdkit ≥ 1.24, Linux only)

This matches the process ID "PID", if the client connects over a Unix domain socket.

Note that process IDs are recycled so this alone is not secure enough to ensure that only a single desired process can connect. However you could use it as an additional check.

(nbdkit ≥ 1.24)

This matches the numeric user ID "UID", if the client connects over a Unix domain socket.

(nbdkit ≥ 1.24)

This matches the numeric group ID "GID", if the client connects over a Unix domain socket.

(nbdkit ≥ 1.24)

These match the CID or port number for "AF_VSOCK" sockets.

If neither the "allow" nor the "deny" parameter is given the filter does nothing.

Unix domain sockets and "AF_VSOCK" sockets were always unfiltered in nbdkit ≤ 1.22. In nbdkit ≥ 1.24 the ability to filter them was added.

Permit known good connections and deny everything else:

 nbdkit --filter=ip ... allow=good1,good2,... deny=all

Block troublemakers but allow everything else:

 nbdkit --filter=ip ... deny=bad1,bad2,...

Set list of allow rules. This parameter is optional, if omitted the allow list is empty.
Set list of deny rules. This parameter is optional, if omitted the deny list is empty.

$filterdir/nbdkit-ip-filter.so
The filter.

Use "nbdkit --dump-config" to find the location of $filterdir.

"nbdkit-ip-filter" first appeared in nbdkit 1.18.

nbdkit(1), nbdkit-exitlast-filter(1), nbdkit-exitwhen-filter(1), nbdkit-limit-filter(1), nbdkit-filter(3).

Richard W.M. Jones

Copyright (C) 2019-2020 Red Hat Inc.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

  • Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
  • Neither the name of Red Hat nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY RED HAT AND CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL RED HAT OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

2021-01-20 nbdkit-1.24.1