DOKK / manpages / debian 12 / i2c-tools / i2cget.8.en
I2CGET(8) System Manager's Manual I2CGET(8)

i2cget - read from I2C/SMBus chip registers

i2cget [-f] [-y] [-a] i2cbus chip-address [data-address [mode [length]]]
i2cget -V

i2cget is a small helper program to read registers visible through the I2C bus (or SMBus).

Display the version and exit.
Force access to the device even if it is already busy. By default, i2cget will refuse to access a device which is already under the control of a kernel driver. Using this flag is dangerous, it can seriously confuse the kernel driver in question. It can also cause i2cget to return an invalid value. So use at your own risk and only if you know what you're doing.
Disable interactive mode. By default, i2cget will wait for a confirmation from the user before messing with the I2C bus. When this flag is used, it will perform the operation directly. This is mainly meant to be used in scripts. Use with caution.
Allow using addresses between 0x00 - 0x07 and 0x78 - 0x7f. Not recommended.

There are two required options to i2cget. i2cbus indicates the number or name of the I2C bus to be scanned. This number should correspond to one of the busses listed by i2cdetect -l. chip-address specifies the address of the chip on that bus, and is an integer between 0x08 and 0x77.

data-address specifies the address on that chip to read from, and is an integer between 0x00 and 0xFF. If omitted, the currently active register will be read (if that makes sense for the considered chip).

The mode parameter, if specified, is one of the letters b, w, c, or i, corresponding to a read byte data, a read word data, a write byte/read byte, an SMBus block read, or an I2C block read transaction, respectively. A p can also be appended to the mode parameter to enable PEC, except for I2C block transactions. If the mode parameter is omitted, i2cget defaults to a read byte data transaction, unless data-address is also omitted, in which case the default (and only valid) transaction is a single read byte.

The length parameter, if applicable and specified, sets the length of the block transaction. Valid values are between 1 and 32. Default value is 32.

i2cget can be extremely dangerous if used improperly. I2C and SMBus are designed in such a way that an SMBus read transaction can be seen as a write transaction by certain chips. This is particularly true if setting mode to cp (write byte/read byte with PEC). Be extremely careful using this program.

Get the value of 8-bit register 0x11 of the I2C device at 7-bit address 0x2d on bus 1 (i2c-1), after user confirmation:

# i2cget 1 0x2d 0x11


Get the value of 16-bit register 0x00 of the I2C device at 7-bit
    address 0x48 on bus 1 (i2c-1), after user confirmation:




# i2cget 1 0x48 0x00 w






Set the internal pointer register of a 24C02 EEPROM at 7-bit
    address 0x50 on bus 9 (i2c-9) to 0x00, then read the first 2 bytes from that
    EEPROM:




# i2cset -y 9 0x50 0x00 ; i2cget -y 9 0x50 ; i2cget -y 9 0x50






This assumes that the device automatically increments its internal
    pointer register on every read, and supports read byte transactions (read
    without specifying the register address, "Receive Byte" in SMBus
    terminology.) Most EEPROM devices behave that way. Note that this is only
    safe as long as nobody else is accessing the I2C device at the same time. A
    safer approach would be to use a "Read Word" SMBus transaction
    instead, or an I2C Block Read transaction to read more than 2 bytes.


Set the internal pointer register of a 24C32 EEPROM at 7-bit
    address 0x53 on bus 9 (i2c-9) to 0x0000, then read the first 2 bytes from
    that EEPROM:




# i2cset -y 9 0x53 0x00 0x00 ; i2cget -y 9 0x53 ; i2cget -y 9 0x53





This again assumes that the device automatically increments its internal pointer
  register on every read, and supports read byte transactions. While the
  previous example was for a small EEPROM using 8-bit internal addressing, this
  example is for a larger EEPROM using 16-bit internal addressing. Beware that
  running this command on a small EEPROM using 8-bit internal addressing would
  actually write 0x00 to the first byte of that EEPROM. The safety
  concerns raised above still stand, however in this case there is no SMBus
  equivalent, so this is the only way to read data from a large EEPROM if your
  master isn't fully I2C capable. With a fully I2C capable master, you would use
  i2ctransfer to achieve the same in a safe and faster way.

Read the first 8 bytes of an EEPROM device at 7-bit address 0x50
    on bus 4 (i2c-4):




# i2cget -y 4 0x50 0x00 i 8














To report bugs or send fixes, please write to the Linux I2C
    mailing list <linux-i2c@vger.kernel.org> with Cc to the current
    maintainer: Jean Delvare <jdelvare@suse.de>.










i2cdetect(8), i2cdump(8), i2cset(8), i2ctransfer(8)










Jean Delvare


This manual page was strongly inspired from those written by David
    Z Maze for i2cset.







  

    July 2021