OUTPUT OPTIONS

By default, "munin-node-configure" will print out a table summarising the results.

--shell

Instead of a table, print shell commands to install the new plugin suggestions.

This implies "--suggest", unless "--snmp" was also enabled. By default, it will not attempt to remove any plugins.

--remove-also

When "--shell" is enabled, also provide commands to remove plugins that are no longer applicable from the service directory.

PLUGIN SELECTION OPTIONS

--families <family,...>

Override the list of families that will be used (auto, manual, contrib, snmpauto). Multiple families can be specified as a comma-separated list, by repeating the "--families" option, or as a combination of the two.

When listing installed plugins, the default families are 'auto', 'manual' and 'contrib'. Only 'auto' plugins are checked for suggestions. SNMP probing is only performed on 'snmpauto' plugins.

--newer <version>

Only consider plugins added to the Munin core since <version>. This option is useful when upgrading, since it can prevent plugins that have been manually removed from being reinstalled. This only applies to plugins in the 'auto' family.

SNMP Options

--snmp <host|cidr,...>

Probe the SNMP agents on the host or CIDR network (e.g. "192.168.1.0/24"), to see what plugins they support. This may take some time, especially if the many hosts are specified.

This option can be specified multiple times, or as a comma-separated list, to include more than one host/CIDR.

--snmpversion <ver>

The SNMP version (1, 2c or 3) to use. ['2c']

--snmpport <port>

The SNMP port to use [161]

--snmpdomain <domain>

The Transport Domain to use for exchanging SNMP messages. The default is UDP/IPv4. Possible values: 'udp', 'udp4', 'udp/ipv4'; 'udp6', 'udp/ipv6'; 'tcp', 'tcp4', 'tcp/ipv4'; 'tcp6', 'tcp/ipv6'.

SNMP 1/2c authentication

SNMP versions 1 and 2c use a "community string" for authentication. This is a shared password, sent in plaintext over the network.

--snmpcommunity <string>

The community string for version 1 and 2c agents. ['public'] (If this works your device is probably very insecure and needs a security checkup).

SNMP 3 authentication

SNMP v3 has three security levels. Lowest is "noAuthNoPriv", which provides neither authentication nor encryption. If a username and "authpassword" are given it goes up to "authNoPriv", and the connection is authenticated. If "privpassword" is also given the security level becomes "authPriv", and the connection is authenticated and encrypted.

Note: Encryption can slow down slow or heavily loaded network devices. For most uses "authNoPriv" will be secure enough -- the password is sent over the network encrypted in any case.

ContextEngineIDs are not (yet) supported.

For further reading on SNMP v3 security models please consult RFC3414 and the documentation for Net::SNMP.

--snmpusername <name>

Username. There is no default.

--snmpauthpassword <password>

Authentication password. Optional when encryption is also enabled, in which case defaults to the privacy password ("--snmpprivpassword").

--snmpauthprotocol <protocol>

Authentication protocol. One of 'md5' or 'sha' (HMAC-MD5-96, RFC1321 and SHA-1/HMAC-SHA-96, NIST FIPS PIB 180, RFC2264). ['md5']

--snmpprivpassword <password>

Privacy password to enable encryption. There is no default. An empty ('') password is considered as no password and will not enable encryption.

Privacy requires a privprotocol as well as an authprotocol and a authpassword, but all of these are defaulted (to 'des', 'md5', and the privpassword value, respectively) and may therefore be left unspecified.

--snmpprivprotocol <protocol>

If the privpassword is set this setting controls what kind of encryption is used to achieve privacy in the session. Only the very weak 'des' encryption method is supported officially. ['des']

munin-node-configure also supports '3des' (CBC-3DES-EDE, aka Triple-DES, NIST FIPS 46-3) as specified in IETF draft-reeder-snmpv3-usm-3desede. Whether or not this works with any particular device, we do not know.