NAME

qcontrol - Hardware control for QNAP Turbo Station

SYNOPSIS

qcontrol -d

qcontrol command value

DESCRIPTION

The utility can be used to control leds or fan speed, or sound the buzzer. As a daemon it can monitor the device for example for button presses or temperature values and trigger actions defined in the LUA configuration file, for example to power off the system or to modify the fan speed.

Note: the current version does not have a real daemon mode. Caution is therefore advised when using qcontrol as a real daemon to monitor and control a device.

Currently supported devices are the QNAP TS-109, QNAP TS-11x, QNAP TS-12x, QNAP TS-209, QNAP HS-210, QNAP TS-21x, QNAP TS-22x, QNAP TS-409, QNAP TS-409U, QNAP TS-41x, QNAP TS-42x and Synology Diskstation and Rackstation. Support for additional devices may be added in future releases.

BASIC USAGE

Normally a control process will be started when the system is booted. This control process opens a socket through which the actual commands can be passed. A control proces is started using either the --daemon or --foreground options.

After that, the actual commands to control devices can be entered:
# qcontrol <command> <value>

Because the socket file is created in /var/run, all commands must be run as root.

OPTIONS

This program follows the usual GNU command line syntax, with long options starting with two dashes (`-'). An overview of supported options is included below.

-d, --daemon

Starts the control process as a background process (daemon mode). Messages will be logged in the syslog.

-f, --foreground

Starts the control process as a foreground process. Mainly useful for testing.

--direct

Allows to execute a qcontrol command without a running control process.

-?, --help

Print command help and info.

-V, --version

Print program version.

SUPPORTED CLIENT COMMANDS

Below an overview of the supported commands that can be sent using the program in client mode, and the allowed values for each.

Commands (these and others) can also be programmed in response to events using the LUA configuration file.

For the leds, values including `1hz' and `2hz' will result in the led flashing on/off in the default or specified color, with the `hz' value determining the speed of the flashes. In the case of `greenred', the led will alternate between green and red instead of on and off.

powerled

Controls the power led (not available on TS-409 and TS-409U).

Values: off | on | 1hz | 2hz

statusled

Controls the status led.

Values:
off | greenon | redon |
green1hz | red1hz | greenred1hz |
green2hz | red2hz | greenred2hz

usbled

Controls the usb led.

Values: off | on | 8hz

buzzer

Sounds the buzzer.

Values: short | long

fanspeed

Controls the speed of the fan (if present).

Values: stop | silence | low | medium | high | full

autopower

Controls the automatic power mechanism.

Values: on | off

KNOWN ISSUES

After running the control process and killing it, the socket file will still exist. This will cause the following error when the control process is started again: `Error binding to socket: Address already in use'.

The solution is to remove the socket file and then try again:
# rm /var/run/qcontrol.sock

The program is not yet very robust against errors in the configuration file.

FILES

/etc/qcontrol.conf

LUA configuration file for qcontrol

/etc/default/qcontrol

Configuration file for qcontrol init script

/var/run/qcontrol.sock

Socket file for communication between daemon precess and client

SEE ALSO

/etc/qcontrol/*.lua

Example LUA configuration files for a variety of platforms

AUTHOR

qcontrol was written by Byron Bradley <byron.bbradley@gmail.com>.

This manual page was written by Frans Pop <fjp@debian.org> for the Debian project (but may be used by others).