| saned(8) | SANE Scanner Access Now Easy | saned(8) |
saned - SANE network daemon
saned [ -a [ username ] ] [ -u username ] [ -b address ] [ -p port ] [ -l ] [ -D ] [ -o ] [ -d n ] [ -e ] [ -h ]
saned is the SANE (Scanner Access Now Easy) daemon that allows remote clients to access image acquisition devices available on the local host.
saned recognises the following options:
If saned is run from other programs such as inetd(8), xinetd(8) and systemd(1), check that program's documentation on how to pass command-line options.
First and foremost: saned is not intended to be exposed to the internet or other non-trusted networks. Make sure that access is limited by tcpwrappers and/or a firewall setup. Don't depend only on saned's own authentication. Don't run saned as root if it's not necessary. And do not install saned as setuid root.
The saned.conf configuration file contains both options for the daemon and the access list.
The access list is a list of host names, IP addresses or IP subnets (CIDR notation) that are permitted to use local SANE devices. IPv6 addresses must be enclosed in brackets, and should always be specified in their compressed form. Connections from localhost are always permitted. Empty lines and lines starting with a hash mark (#) are ignored. A line containing the single character ``+'' is interpreted to match any hostname. This allows any remote machine to use your scanner and may present a security risk, so this shouldn't be used unless you know what you're doing.
A sample configuration file is shown below:
The case of the host names does not matter, so AHost.COM is considered identical to ahost.com.
For saned to work properly in its default mode of operation, it is also necessary to add the appropriate configuration for xinetd(8), inetd(8) or systemd(1) (see below). Note that your inetd(8) must support IPv6 if you want to connect to saned over IPv6; xinetd(8), openbsd-inetd(8) and systemd(1) are known to support IPv6, check the documentation for your inetd(8) daemon.
In the sections below the configuration for inetd(8), xinetd(8) and systemd(1) are described in more detail.
For the configurations below it is necessary to add a line of the following form to /etc/services:
The official IANA short name for port 6566 is "sane-port". The older name "sane" is now deprecated.
It is required to add a single line to the inetd(8) configuration file (/etc/inetd.conf)
The configuration line normally looks like this:
However, if your system uses tcpd(8) for additional security screening, you may want to disable saned access control by putting ``+'' in saned.conf and use a line of the following form in /etc/inetd.conf instead:
Note that both examples assume that there is a saned group and a saned user. If you follow this example, please make sure that the access permissions on the special device are set such that saned can access the scanner (the program generally needs read and write access to scanner devices).
If xinetd(8) is installed on your system instead of inetd(8) the following example for /etc/xinetd.conf may be helpful:
# default: off
# description: The sane server accepts requests
# for network access to a local scanner via the
# network.
service sane-port
{
port = 6566
socket_type = stream
wait = no
user = saned
group = saned
server = /usr/sbin/saned
}
saned can be compiled with explicit systemd(1) support. This will allow logging debugging information to be forwarded to the systemd(1) journal. The systemd(1) support requires compilation with the systemd-devel package installed on the system. This is the preferred option.
saned can be used with systemd(1) without the systemd(1) integration compiled in, but then logging of debug information is not supported.
The systemd(1) configuration is different for the 2 options, so both are described below.
For systemd(1) configuration we need to add 2 configuration files in /etc/systemd/system.
The first file we need to add here is called saned.socket. It shall have the following contents:
[Unit] Description=saned incoming socket [Socket] ListenStream=6566 Accept=yes MaxConnections=1 [Install] WantedBy=sockets.target
The second file to be added is saned@.service with the following contents:
[Unit] Description=Scanner Service Requires=saned.socket [Service] ExecStart=/usr/sbin/saned User=saned Group=saned StandardInput=null StandardOutput=syslog StandardError=syslog Environment=SANE_CONFIG_DIR=/etc/sane.d # If you need to debug your configuration uncomment the next line and # change it as appropriate to set the desired debug options # Environment=SANE_DEBUG_DLL=255 SANE_DEBUG_BJNP=5 [Install] Also=saned.socket
You need to set an environment variable for SANE_CONFIG_DIR pointing to the directory where saned can find its configuration files. You will have to remove the # on the last line and set the variables for the desired debugging information if required. Multiple variables can be set by separating the assignments by spaces as shown in the example above.
Unlike xinetd(8) and inetd(8), systemd(1) allows debugging output from backends set using SANE_DEBUG_XXX to be captured. See the man-page for your backend to see what options are supported. With the service unit as described above, the debugging output is forwarded to the system log.
This configuration will also work when saned is compiled WITH systemd(1) integration support, but it does not allow debugging information to be logged.
For systemd(1) configuration for saned, we need to add 2 configuration files in /etc/systemd/system.
The first file we need to add here is called saned.socket. It is identical to the version for systemd(1) with the support compiled in. It shall have the following contents:
[Unit] Description=saned incoming socket [Socket] ListenStream=6566 Accept=yes MaxConnections=1 [Install] WantedBy=sockets.target
The second file to be added is saned@.service. This one differs from the version with systemd(1) integration compiled in:
[Unit] Description=Scanner Service Requires=saned.socket [Service] ExecStart=/usr/sbin/saned User=saned Group=saned StandardInput=socket Environment=SANE_CONFIG_DIR=/etc/sane.d [Install] Also=saned.socket
user:password:backend
access to the listed backends is restricted. A backend may be listed multiple times for different user/password combinations. The server uses MD5 hashing if supported by the client.
sane(7), scanimage(1), xscanimage(1),
xcam(1), sane-dll(5), sane-net(5),
sane-"backendname"(5), inetd(8), xinetd(8),
systemd(1)
http://www.penguin-breeder.org/?page=sane-net
David Mosberger
| 29 Sep 2017 |