Smokeping::probes::OpenSSHEOSPing - Arista EOS SSH Probe for
SmokePing
*** Probes ***
+OpenSSHEOSPing
forks = 5
offset = 50%
packetsize = 100
step = 300
timeout = 15
# The following variables can be overridden in each target section
eospass = password # mandatory
eosuser = user # mandatory
pings = 5
psource = 192.168.2.129
source = 192.168.2.1 # mandatory
unpriv = 1
# [...]
*** Targets ***
probe = OpenSSHEOSPing # if this should be the default probe
# [...]
+ mytarget
# probe = OpenSSHEOSPing # if the default probe is something else
host = my.host
eospass = password # mandatory
eosuser = user # mandatory
pings = 5
psource = 192.168.2.129
source = 192.168.2.1 # mandatory
unpriv = 1
Connect to Arista EOS via OpenSSH to run ping commands. This probe
uses the "ping" cli of the Arista EOS. You have the option to
specify which interface the ping is sourced from as well.
Supported probe-specific variables:
- forks
- Run this many concurrent processes at maximum
Example value: 5
Default value: 5
- offset
- If you run many probes concurrently you may want to prevent them from
hitting your network all at the same time. Using the probe-specific offset
parameter you can change the point in time when each probe will be run.
Offset is specified in % of total interval, or alternatively as 'random',
and the offset from the 'General' section is used if nothing is specified
here. Note that this does NOT influence the rrds itself, it is just a
matter of when data acqusition is initiated. (This variable is only
applicable if the variable 'concurrentprobes' is set in the 'General'
section.)
Example value: 50%
- packetsize
- The (optional) packetsize option lets you configure the packetsize for the
pings sent.
Default value: 100
- step
- Duration of the base interval that this probe should use, if different
from the one specified in the 'Database' section. Note that the step in
the RRD files is fixed when they are originally generated, and if you
change the step parameter afterwards, you'll have to delete the old RRD
files or somehow convert them. (This variable is only applicable if the
variable 'concurrentprobes' is set in the 'General' section.)
Example value: 300
- timeout
- How long a single 'ping' takes at maximum
Example value: 15
Default value: 5
Supported target-specific variables:
- eospass
- The eospass option allows you to specify the password for the username
specified with the option eosuser.
Example value: password
This setting is mandatory.
- eosuser
- The eosuser option allows you to specify a username that has ping
capability on the EOS Device.
Example value: user
This setting is mandatory.
- pings
- How many pings should be sent to each target, if different from the global
value specified in the Database section. Note that the number of pings in
the RRD files is fixed when they are originally generated, and if you
change this parameter afterwards, you'll have to delete the old RRD files
or somehow convert them.
Example value: 5
- psource
- The (optional) psource option specifies an alternate IP address or
Interface from which you wish to source your pings from. Routers can have
many many IP addresses, and interfaces. When you ping from a router you
have the ability to choose which interface and/or which IP address the
ping is sourced from. Specifying an IP/interface does not necessarily
specify the interface from which the ping will leave, but will specify
which address the packet(s) appear to come from. If this option is left
out the EOS Device will source the packet automatically based on routing
and/or metrics. If this doesn't make sense to you then just leave it out.
Example value: 192.168.2.129
- source
- The source option specifies the EOS device that is going to run the ping
commands. This address will be used for the ssh connection.
Example value: 192.168.2.1
This setting is mandatory.
- unpriv
- If the account is unprivileged, specify the 'unpriv' option. You must also
configure "pings = 5", since that is the only value supported,
and values specified for packetsize or psource are ignored.
Example value: 1
Bill Fenner <fenner@aristanetworks.com>
based on Smokeping::Probes::OpenSSHJunOSPing by Tobias Oetiker
<tobi@oetiker.ch>, which itself is based on
Smokeping::probes::TelnetJunOSPing by S H A N <shanali@yahoo.com>.
EOS configuration
The EOS device should have a username/password configured, and the
ssh server must not be disabled.
Make sure to connect to the remote host once from the commmand
line as the user who is running smokeping. On the first connect ssh will ask
to add the new host to its known_hosts file. This will not happen
automatically so the script will fail to login until the ssh key of your EOS
box is in the known_hosts file.
This module requires the Net::OpenSSH and IO::Pty perl
modules.