smp_zone_lock - invoke ZONE LOCK SMP function
smp_zone_lock [--expected=EX] [--fpass=FP]
[--help] [--hex] [--inactivity=TL]
[--interface=PARAMS] [--password=PA] [--raw]
[--sa=SAS_ADDR] [--verbose] [--version]
SMP_DEVICE[,N]
Sends a SAS Serial Management Protocol (SMP) ZONE LOCK function
request to an SMP target. The SMP target is identified by the
SMP_DEVICE and the --sa=SAS_ADDR. Depending on the interface,
the SAS_ADDR may be deduced from the SMP_DEVICE. The mpt
interface uses SMP_DEVICE to identify a HBA (an SMP initiator) and
needs the additional ,N to differentiate between HBAs if there are
multiple present.
Mandatory arguments to long options are mandatory for short
options as well.
- -E,
--expected=EX
- set the 'expected expander change count' field in the SMP request. The
value EX is from 0 to 65535 inclusive with 0 being the default
value. When EX is greater than zero then if the value doesn't match
the expander change count of the SMP target (i.e. the expander) when the
request arrives then the target ignores the request and sets a function
result of "invalid expander change count" in the response.
- -F,
--fpass=FP
- where FP is the name of a file which contains the password. The
password may be in ASCII in which case it is on one line surrounded by
either single quotes are double quotes. Alternatively the password may be
given in ASCII hexadecimal; either as bytes separated by space, tab, comma
or newline, or as longer strings of hexadecimal bytes in which every 2
digits represents a byte. Empty lines and those starting with
"#" are ignored.
- -h, --help
- output the usage message then exit.
- -H, --hex
- output the response (less the CRC field) in hexadecimal.
- -i,
--inactivity=TL
- sets the zone lock inactivity time limit to TL which has units of
100 milliseconds. The default value is 0 which implies no time limit.
- -I,
--interface=PARAMS
- interface specific parameters. In this case "interface" refers
to the path through the operating system to the SMP initiator. See the
smp_utils man page for more information.
- -P,
--password=PA
- where PA is the zone manager password which may be up to 32 bytes
long. This option cannot be give together with the --fpass=FP
option. The default password is 32 NULLs (zero bytes) and PA is
padded with NULLs to the right (to make it 32 bytes long in the
request).
- -r, --raw
- send the response (less the CRC field) to stdout in binary. All error
messages are sent to stderr.
- -s,
--sa=SAS_ADDR
- specifies the SAS address of the SMP target device. The mpt interface
needs this option and it will typically be an expander's SAS address. The
SAS_ADDR is in decimal but most SAS addresses are shown in
hexadecimal. To give a number in hexadecimal either prefix it with '0x' or
put a trailing 'h' on it.
- -v, --verbose
- increase the verbosity of the output. Can be used multiple times.
- -V, --version
- print the version string and then exit.
The SMP ZONE LOCK function was introduced in SAS-2 .
Written by Douglas Gilbert.
Report bugs to <dgilbert at interlog dot com>.
Copyright © 2011 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty;
not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
smp_utils, smp_zone_activate, smp_zone_unlock,
smp_ena_dis_zoning(smp_utils)