tjoin performs a trivial side-by-side join of multiple
tables. The N'th row of the output table consists of the N'th row of the
first input table, followed by the N'th row of the second input table, ...
and so on. It is suitable if you want to amalgamate two or more tables whose
row orderings correspond exactly to each other.
For the (more usual) case in which the rows of the tables to be
joined are not already in the right order, use one of the crossmatching
commands.
- nin=<count>
The number of input tables for this task. For each of the
input tables N there will be associated parameters
ifmtN,
inN
and
icmdN.
- ifmtN=<in-format>
Specifies the format of input table #N as specified by
parameter
inN. The known formats are listed in SUN/256. This flag can
be used if you know what format your table is in. If it has the special value
(auto) (the default), then an attempt will be made to detect the format
of the table automatically. This cannot always be done correctly however, in
which case the program will exit with an error explaining which formats were
attempted. This parameter is ignored for scheme-specified tables.
- inN=<tableN>
The location of input table #N. This may take one of the
following forms:
- A filename.
- A URL.
- The special value "-", meaning standard input. In this
case the input format must be given explicitly using the ifmtN
parameter. Note that not all formats can be streamed in this way.
- A scheme specification of the form
:<scheme-name>:<scheme-args>.
- A system command line with either a "<" character at
the start, or a "|" character at the end
("<syscmd" or "syscmd|"). This
executes the given pipeline and reads from its standard output. This will
probably only work on unix-like systems.
In any case, compressed data in one of the supported compression formats (gzip,
Unix compress or bzip2) will be decompressed transparently.
- icmdN=<cmds>
Specifies processing to be performed on input table #N as
specified by parameter
inN, before any other processing has taken
place. The value of this parameter is one or more of the filter commands
described in SUN/256. If more than one is given, they must be separated by
semicolon characters (";"). This parameter can be repeated multiple
times on the same command line to build up a list of processing steps. The
sequence of commands given in this way defines the processing pipeline which
is performed on the table.
Commands may alteratively be supplied in an external file, by
using the indirection character '@'. Thus a value of
"@filename" causes the file filename to be read for
a list of filter commands to execute. The commands in the file may be
separated by newline characters and/or semicolons, and lines which are blank
or which start with a '#' character are ignored.
- ocmd=<cmds>
Specifies processing to be performed on the output table,
after all other processing has taken place. The value of this parameter is one
or more of the filter commands described in SUN/256. If more than one is
given, they must be separated by semicolon characters (";"). This
parameter can be repeated multiple times on the same command line to build up
a list of processing steps. The sequence of commands given in this way defines
the processing pipeline which is performed on the table.
Commands may alteratively be supplied in an external file, by
using the indirection character '@'. Thus a value of
"@filename" causes the file filename to be read for
a list of filter commands to execute. The commands in the file may be
separated by newline characters and/or semicolons, and lines which are blank
or which start with a '#' character are ignored.
- omode=out|meta|stats|count|checksum|cgi|discard|topcat|samp|tosql|gui
The mode in which the result table will be output. The
default mode is
out, which means that the result will be written as a
new table to disk or elsewhere, as determined by the
out and
ofmt parameters. However, there are other possibilities, which
correspond to uses to which a table can be put other than outputting it, such
as displaying metadata, calculating statistics, or populating a table in an
SQL database. For some values of this parameter, additional parameters
(
<mode-args>) are required to determine the exact behaviour.
Possible values are
- out
- meta
- stats
- count
- checksum
- cgi
- discard
- topcat
- samp
- tosql
- gui
Use the
help=omode flag or see SUN/256 for more information.
- out=<out-table>
The location of the output table. This is usually a
filename to write to. If it is equal to the special value "-" (the
default) the output table will be written to standard output.
This parameter must only be given if omode has its default
value of "out".
- ofmt=<out-format>
Specifies the format in which the output table will be
written (one of the ones in SUN/256 - matching is case-insensitive and you can
use just the first few letters). If it has the special value
"
(auto)" (the default), then the output filename will be
examined to try to guess what sort of file is required usually by looking at
the extension. If it's not obvious from the filename what output format is
intended, an error will result.
This parameter must only be given if omode has its default
value of "out".
- fixcols=none|dups|all
Determines how input columns are renamed before use in
the output table. The choices are:
- none: columns are not renamed
- dups: columns which would otherwise have duplicate names in the
output will be renamed to indicate which table they came from
- all: all columns will be renamed to indicate which table they came
from
If columns are renamed, the new ones are determined by
suffix*
parameters.
- suffixN=<label>
If the
fixcols parameter is set so that input
columns are renamed for insertion into the output table, this parameter
determines how the renaming is done. It gives a suffix which is appended to
all renamed columns from table N.